Christmas Trinket: Seed Bead Tree Earrings or Ornaments on Eye Pins

0 comments  •   6 minute read

Pair of Christmas trinket earrings: little seed bead trees built on eye pins with a blue bead bauble at the base

Eight short rows of seed beads on eye pins, stacked into a triangle and held together by two beaded side rods: that's the whole trick behind this little Christmas tree. A blue bauble swings from the bottom, every row is sprinkled with colored "ornaments," and the finished tree works as an earring, a tree decoration or a gift-tag charm.

Helena Chmelíková designed the Christmas Trinket for Preciosa Ornela. It's a good first eye-pin project: there's no stitching, just stringing and making neat loops with round-nose pliers. Bead sizes are given in aught (10/0). All other measurements are imperial with metric in parentheses.

Pair of Christmas Trinket earrings: small seed bead trees in sea green with colored accents and a blue bead at the base, on gold ear wires

Project card

Difficulty ●○○ beginner
Technique Eye pins and simple loops
Beads 10/0 PermaLux, one 6 mm round
Colors
Download PDF

One button adds all seven bead colors, the 6 mm round, gold eye pins in two lengths, jump rings and ear wires. You'll have plenty left for a second pair or a few tree ornaments.

Materials & Tools

From our shelves

From your sewing basket

  • A small ruler, for trimming wire evenly
  • A silicone earring back or a bead stopper, to hold the first side rod while you work
  • Ribbon or gold thread, if you're making ornaments instead of earrings
Components: gold ear wires, eye pins in several lengths, jump rings and a silicone earring stop
Ear wires, eye pins, rings and a stop
Tools: round-nose pliers, two flat-nose pliers, flush cutters and a ruler
Pliers, cutters and a ruler

Sizing note: 10/0 or 8/0

Preciosa's original uses 8/0 Terra Intensive Lining beads, which we don't carry. This version uses 10/0 PermaLux, which gives a tree about 20–25% smaller and a little finer. To match the original size, add one R1 bead to every row and one extra spacer bead between eyes on each side rod.

The Palette

A deep sea green carries the tree, and six bright ornament colors are scattered through the rows. There's no fixed spot for any ornament bead: place them wherever they look good, and no two trees come out the same.

Christmas Trinket: tree and ornaments

Sea Green for the tree, with yellow, orange, pink, red and blue ornaments scattered through every row.

Open this palette in the Color Studio

In the Color Studio you can swap the tree color or any ornament for another bead in stock and see the set side by side before you buy.

Pattern Notes

The tree has eight horizontal rows, counted from the top, plus two side rods that thread through the eyes at each end of the rows. Each row mixes the tree color (R1) with a few ornament beads (R2). Put the R2 beads anywhere in the row.

Row Ornament (R2) Tree color (R1)
1 (top) 1 0
2 1 1
3 1 2
4 1 3
5 2 3
6 1 5
7 2 5
8 (bottom, with bauble) 2 6
Side rod 1 4 5
Side rod 2 3 6

Per tree: about 36 R1 and 18 R2 (3 of each ornament color), plus one 6 mm round. Each side rod has 9 beads: one at each end and one between every pair of row eyes.

A small pile of sea green tree-color beads
R1, the tree color
A small pile of mixed yellow, orange, pink, red and blue ornament beads
R2, the ornament mix

Step-by-Step

  1. Make the bauble. Slide the 6 mm round onto a 1 in (25 mm) eye pin and trim the wire to about 3/8 in (8–9 mm) above the bead. Grip the very end of the wire in round-nose pliers and roll it into a loop, holding the bead and wire steady with your other hand. Center the loop over the bead hole by bending it back gently at the base. Open a jump ring with two flat-nose pliers, hook on the bauble, and close it.
    Blue round bead on an eye pin, shown at stages of forming a loop
    Rolling the loop
    Finished blue bauble with a centered loop and a gold ring
    The finished bauble
  2. Sort your beads. Make two piles: R1 in one, all the R2 ornament colors mixed in the other. Working from piles keeps the rows random without stopping to choose every bead.
  3. Build the bottom row. On a 2 in (50 mm) eye pin, string half the row 8 beads, the ring holding the bauble, then the other half. Trim the wire, leaving about 3/8 in (8–9 mm), and roll a second loop the same size as the first. Twist both loops so they sit flat in the same plane, then tilt them slightly toward each other.
    Bottom row strung with the bauble hanging in the middle, wire still long
    Strung, wire not yet trimmed
    Bottom row finished with matching loops at both ends
    Matching loops at both ends
  4. Make rows 1 to 7. String each row from the table onto an eye pin, trim, and roll the second loop. Use the 1 in (25 mm) pins for the short top rows and trimmed 2 in (50 mm) pins for the longer ones. Tilt both loops of each row slightly downward so the rows will hang at an angle on the side rods.
    Eye pins of four different lengths
    Pins trimmed to length
    Eight finished rows laid out from shortest to longest, forming a triangle
    All eight rows
  5. Add the side rods. On a 2 in (50 mm) eye pin, string 1 bead, then the left-hand loop of the bottom row, 1 bead, the next row's loop, and so on up to the top row. Finish with 1 bead above the top loop. Hold the end with a silicone earring back or bead stopper. String the second side rod through the right-hand loops the same way, trim it and roll the loop. Then remove the stopper from the first rod, trim it and roll its loop.
    Tree with the first side rod strung and held by a clear earring stop
    First rod, held with a stop
    Tree with both side rods in place
    Both rods in place
    Finished tree with both rod ends looped at the top
    Loops closed at the top
  6. Finish. Open a jump ring, pass it through both top loops and the ear wire, and close it. Make the second earring the same way.
    Close-up of a jump ring joining both rods to a gold ear wire
    Joining the ear wire
    Finished pair of tree earrings
    The finished pair

Tips

  • Measure the wire, don't eyeball it. Leave about 3/8 in (8–9 mm) of wire for each loop. Loops that match in size are what make the tree look neat.
  • Keep loops in one plane. After rolling each loop, check that both ends of a row face the same way. A twisted row won't thread onto the side rods cleanly.
  • Tilt before you assemble. Angling the loops (toward each other on the bottom row, downward on the rest) gives the tree its sloped sides. It's much harder to adjust once the rods are on.
  • Open rings sideways. Twist jump rings open front to back rather than pulling the ends apart, so they close without a gap.

Variations

  • Tree ornament or gift tag. Skip the ear wire and tie a loop of ribbon or gold thread through the top ring.
  • Golden tree. Use Light Yellow as the tree color with a few Orange ornaments, as in Preciosa's yellow version.
  • Lime tree. Try Mint or Teal for the tree with a red or gold bauble.
  • Bigger tree. Use 8/0 seed beads with the same row counts, or follow the sizing note above to match the original with 10/0s.
Tree trinkets as ornaments on pink ribbon and gold thread, and as earrings in green, teal, yellow and lime
Ornaments and earrings in four colorways

Make it yours

Plan your own tree in the free Color Studio: pick a tree color, see which ornament colors go with it, and build the set before you buy. When you have a palette you like, the Pattern Studio turns it into a bead pattern.

Open the Color Studio

Design credit: Preciosa Ornela / Helena Chmelíková. Instructions and photos adapted for clarity for the Shipwreck Beads blog.

Previous Next

Leave a comment

Please note: comments must be approved before they are published.