A small brick stitch triangle, 11 beads across at the base, turns into a Christmas tree with a scatter of colored ornaments, a gold glint here and there, and a red bead on top for the star. Each earring takes well under 100 beads and an evening, and the pattern is easy to read once the first two rows are in.
Alexandra Lysenko designed the Merry Christmas earrings for Preciosa Ornela in PermaLux Teal Matte, with bright PermaLux ornaments and touches of gold. Bead sizes are given in aught (10/0, 8/0). All other measurements are imperial with metric in parentheses.
Project card
| Difficulty | ●●○ intermediate |
| Technique | Brick stitch |
| Beads | 10/0 tree and ornaments, one 8/0 per earring |
| Size | About 1 in (2.5 cm) wide at the base |
| Colors | plus bright PermaLux ornaments |
One button adds the teal, red and gold beads, four ornament colors, WildFire line, size 12 needles, jump rings and ear wires. Bring your own scissors and pliers.
Materials & Tools
From our shelves
- PermaLux Teal Matte, 10/0, 55 beads per earring (the tree)
- PermaLux Red, 8/0, 1 bead per earring (the star)
- Silver-Lined Light Gold, 10/0, 2 beads per earring. For the original 24 karat look, use 24 Karat Gold Plate 10/0.
- Ornament colors, 10/0, about 6 beads per earring in a mix: Light Pink, Light Yellow, Blue and Purple
- WildFire .004 in (0.1 mm) line, frost
- Size 12 beading needles
- 4 mm jump rings, one per earring
- Ear wires, one pair
From your sewing basket
- Small sharp scissors
- Two pairs of pliers (flat or chain nose) for the jump rings. See our beading tools if you need a pair.

The Palette
Teal Matte reads as a soft, snowy evergreen, and the PermaLux ornaments pop against it like lights on a real tree. Scatter the ornament colors however you like; no two trees need to match.
-
Permalux Teal Matte 10/0 - 25GM
$7.19
-
Permalux Red 8/0 Loose
$8.25
-
Permalux Light Pink 10/0 - 25GM
$7.67
-
Permalux Light Yellow 10/0 - 25GM
$8.25
-
Permalux Blue 10/0 - 25GM
$8.09
-
Permalux Purple 10/0 - 25GM
$8.09
Teal Matte for the tree, a red 8/0 on top, and bright PermaLux ornaments scattered through the branches.
Open this palette in the Color Studio
In the Color Studio you can swap the tree or ornament colors for any bead we have in stock and see them side by side before you buy.
Pattern Notes
Brick stitch builds a shape row by row, each new bead caught on the thread loop between two beads of the row below. Each row is one bead shorter than the last, which makes the triangle. You start with the widest row, work up to the point, then come back down to add the trunk.


| Bead | Per earring | Preciosa no. |
|---|---|---|
| Teal Matte 10/0 (tree) | 55 | 22M18 |
| Ornament mix 10/0 | 11 (shared between the pair) | PermaLux mix |
| Red 8/0 (star) | 1 | 22008 |
| Gold 10/0 | 2 | 68304 |
Preciosa lists 55 teal, 11 mix, 2 red and 4 gold for the pair; the chart shows the teal count per earring. One 25 g pack of each color is plenty.
Step-by-Step
Prefer to watch? This video follows the same steps.
-
Start the line. Cut about 59 in (1.5 m) of line and thread the needle. String two teal beads, slide them to the far end, and tie a double knot to hold them.

2a · two beads, double knot -
Make the base row. Build the widest row first: 11 teal beads joined side by side, following diagram 1b. Add each bead by passing back through the previous one so the beads stand in a neat line rather than a strand.

2b 
2c 
2d 
2e · the 11-bead base -
Brick stitch the next row. Pick up one bead, pass the needle under the thread loop between the last two beads of the base row, then go back up through the new bead. Keep adding beads across the row the same way, swapping in ornament and gold beads where the chart shows them.

3a · under the loop 
3b · back up the bead 
3d · a gold ornament 
3g · row two done -
Work up to the point. Keep adding rows the same way, one bead shorter each time, until the triangle comes to a point at row 11. Finish with the red 8/0 on top for the star.

4b 
4f · halfway 
4h · the point 
4ch · the red star -
Add the trunk and finish. Weave down through the beads to the base row and stitch the one-bead trunk (row 1) to its center. Hide the line with a few stitches between beads, then trim it close.

5a 
5c · the trunk 
5d · finished -
Add the ear wire. Open a 4 mm jump ring sideways with two pairs of pliers, hook it through the red top bead and the ear wire's loop, and close it. Make the second earring the same way.

6a · jump ring to ear wire 
6b · the pair
Tips
- Get the base row right. Every row above depends on it. Count to 11 and check that the beads sit side by side before you start brick stitching.
- Tension makes the triangle. Snug each bead down firmly so the rows lock together. Loose tension gives a floppy tree that won't hold its shape.
- Plan the ornaments. Lay out the ornament beads for each row before you stitch it, so the colors spread evenly instead of bunching on one side.
- Mirror the pair. You don't need matching ornaments, but keeping the gold beads in the same rows on both earrings makes them read as a pair.
Variations
- Classic green. Swap the teal for PermaLux Sea Green for a traditional evergreen tree.
- Gold and red only. Use just red and gold ornaments for a more formal, old-fashioned look.
- An ornament or gift tag. Skip the ear wire and tie a loop of thread or ribbon through the top bead to hang it on a tree or a present.
- A pendant. Add a jump ring and slide it onto a chain for a matching necklace.

Make it yours
Pick your own tree and ornament colors in the free Color Studio: choose a bead, see what goes with it, and build a palette before you buy. The Pattern Studio can turn a palette into a brick stitch pattern of your own.
Open the Color StudioDesign credit: Preciosa Ornela / Alexandra Lysenko. Instructions and photos adapted for clarity for the Shipwreck Beads blog.